| Items |
 /Asset/I-95.jpg I-95 I-95® Sectional Drain Cleaner |
 /Asset/Root66.jpg Root 66 Root 66® Sectional Drain Cleaner |
 /Asset/Model88.jpg Model 88 Model 88® Sectional Drain Cleaner |
 /Asset/RodRunner.jpg Rodrunner Rodrunner® Sectional Drain Cleaner |
 /Asset/Model-E.jpg Rodrunner Model E Rodrunner® Model E® Sectional Drain Cleaner |
|||||
| Description |
It's three machines in one. With the I-95, you can clear 2"– 3" lines up to 125 ft. long with 5/8" x 7-1/2' sections, clear 4" lines up to 150 ft. long with 7/8" x 15' sections – or use 5/16" cables for small drain work. You switch from 7/8" to 5/8" and back by repositioning the chuck cone. Attach a small drum to the back of the machine to drive smaller cables. |
Uses Sectional Cables for 1-1/4 in. thru 4 in. The Root 66® is a real advance in sectional cable machine design. No mid-range machine has its versatility and power. Look at its versatility. You can drive 5/8 in. cables for lines up to 3 in. and 7/8 in. cables for 4 in. lines - and you can switch from one to the other in seconds, without touching the jaws, without an adapter, without tools. And for sink drain work, slip on a drum that holds smaller cables. |
You Walk While It Works This machine is almost as easy to run as a lawn mower. You push eight or ten foot cable sections into the line until you reach some resistance. Then attach the rear cable coupling to the machine, stand behind it, and turn it on. Watch the cable feed itself into the line. When a section has run into the drain, attach another one and keep going. This self-feeding feature also works to pull sections out of the line. |
Self-Feeds Reinforced Sectional Cables The Rodrunner offers all the features that contractors like in a sectional sewer cleaner - light weight, high speed cable rotation, and short, quick-coupling cables. |
Drives Municipal Rods or Sectional Cables The Model "E" gasoline powered Rodrunner is ideal for cleaning long runs up to 500 ft. down the line. It can be coupled to either 10 ft. sectional cables to clear up to 14 in. lines, or 5/16 in. municipal rods to clear lines up to 24 in. in diameter. The operator stands behind the machine and walks cables or rods into line. |
|||||
| Brands | I-95® | Root 66® | Rodrunner® | Rodrunner® | ||||||
| Weight without Cable | 80 lb36 kg | |||||||||
| Weight | 89 lb18 kg | 42 lb19 kg | 90 lb41 kg | 185 lb84 kg | ||||||
| Depth | 16 in.41 cm | 16 in.40 cm | ||||||||
| Width | 14 in.35 cm | 14 in.35 cm | 21 in.53 cm | 22 in.56 cm | 29 in.74 cm | |||||
| Length | 44 in.112 cm | |||||||||
| Height | 17 in.43 cm | 17 in.43 cm | 40 in.102 cm | |||||||
| Height with Handle Folded Down | 16 in.41 cm | 19 in.48 cm | ||||||||
| Motor Power | 1/3 hp at 400 rpm. | 1/2 hp at 400 rpm. | 3/4 hp at 500 rpm. | 3/4 hp at 485 rpm. | 6-1/2 hp gas engine. | |||||
| Adjustable Chuck | Has two sets of notches; one for 5/8 in. cables and one for 7/8 in. cables. Switch from one to the other in seconds. Pull down handle to engage, lift to stop. Brake stops spinning drums instantly. Chuck handle also acts as lifting handle. | |||||||||
| Chuck Jaws | Drive both 5/8 in. and 7/8 in. cables; also grip drum for smaller diameter cables. | |||||||||
| Drum | Drum holds 25 ft. x 5/16 in. cable for 1-1/2 in. to 2 in. lines, or 35 ft. x 3/8 in. cable for 2 in. to 3 in. lines. | Drum holds 25 ft. x 5/16 in. cable for 1-1/2 in. to 2 in. lines, or 35 ft. x 3/8 in. cable for 2 to 3 in. lines. | ||||||||
| Cables | Cat # 15R10 or 15R10P with Proflex® inner core - 15 ft. x 7/8 in. (4.6 m x 22 mm) for 2 in. to 4 in. (50 mm - 100 mm) lines. Cat # 7.5R8 - 7-1/2 ft. x 5/8 in. (2.3 m x 15.6 mm) for 1-1/4 in. to 3 in. (30 mm - 75 mm) lines. | Cat # 15R10 or 15R10P with Proflex® inner core - 15 ft. x 7/8 in. (4.6 m x 22 mm) for 2 in. to 4 in. (50 mm - 100 mm) lines. Cat # 7.5R8 - 7-1/2 ft. x 5/8 in. (2.3 m x 15.6 mm) for 1-1/4 in. to 3 in. (30 mm - 75 mm) lines. | Cat # 10GP - 10 ft x 1-1/4 in. (3 m x 32 mm) with G-Connector for 3 in. to 10 in. (75 mm - 250 mm) lines. Cat # 8LP or 10LP - 8 ft or 10 ft x 1-1/4 in. 2.4 m or 3 m x 32 mm) with L-Connector for 3 in. to 10 in. (75 mm - 250 mm) lines. | Cat # 10GP Proflex or 10GF Flexichain sections- 10 ft x 1-1/4 in. (3 m x 32 mm) with G-Connector for 3 in. to 10 in. (75 mm - 250 mm) lines. Cat # 15R11 or 15R14 sections - 15 ft x 1-1/4 in. (4.6 m x 32 mm) with R-Connector for 3 in. to 10 in. (75 mm - 250 mm) lines. Cat # 8LP or 10LP Proflex or 8LF or 10LF Flexichain sections - 8 ft or 10 ft x 1-1/4 in. 2.4 m or 3 m x 32 mm) with L-Connector for 3 in. to 10 in. (75 mm - 250 mm) lines. | Cat # 10GP - 10 ft x 1-1/4 in. (3 m x 32 mm) with G-Connector for 3 in. to 10 in. (75 mm - 250 mm) lines. Cat # 2MSR or 3MSR - 36 in. or 39 in. x 5/16 in. (.9 m or 1 m x 9.5 mm) Municipal Rods for 4 in. to 24 in. (100 mm - 600 mm) lines. Cat # 8LP or 10LP - 8 ft or 10 ft x 1-1/4 in. 2.4 m or 3 m x 32 mm) with L-Connector for 3 in. to 10 in. (75 mm - 250 mm) lines. | |||||
| Leather Gloves | With double-reinforced palm, for hand protection when guiding cable. | With double-reinforced palm, for hand protection when guiding cable. | ||||||||
| Cutter Sets |
Cutter Set for 7/8 in. cables includes Spear Head, 2 in. U-Cutter, 3 in. U-Cutter, Hook Auger, and Retrieving Tool. Cutter Set for 5/8 in. cables includes Arrow Head, Boring Gimlet, 1-1/2 in. U-Cutter, and Retrieving Tool. |
Cutter Set for 7/8 in. cables includes Spear Head, 2 in. U-Cutter, 3 in. U-Cutter, Hook Auger, and Retrieving Tool. Cutter Set for 5/8 in. cables includes Arrow Head, Boring Gimlet, 1-1/2 in. U-Cutter, and Retrieving Tool. |
||||||||
| Industry Standards | UL Listed | UL Listed | UL Listed | UL Listed | ||||||
| Gear Head | Rugged cast iron body, ball bearings, cut gears. | |||||||||
| Wheels | 10 in. rubber rear wheels, 6 in. solid rubber caster wheel. | 10 in. rear wheels, 5 in. caster wheel. | ||||||||
| Combination Hand or Foot Operated Power Switch | Air activated for safety; no electrical connection between motor and switch; can be used as hand or foot switch. 11 foot air hose. | Air activated for safety; no electrical connection between motor and switch; can be used as hand or foot switch. 11 foot air hose. | ||||||||
| Power Switch | Has an "off" position to de-activate the control switch. | |||||||||
| Adjustable Safety Clutch | Factory set at 18 - 20 ft. lbs. Protected by a tamper-resistant snap-on cover. | |||||||||
| Engine | 6.5 hp Briggs and Stratton 4 cycle with throttle on handle | |||||||||
| Transmission | Snow and Nabstedt reversing "hot-shift" transmission drives 3/4 in. lifetime lubricated roller chain. No clutch or throttle needed. | |||||||||
| Speed Range | From 100 rpm to 200 rpm for municipal rods; 200 to 400 rpm for sectional cables. | |||||||||
| Slip Clutch | Protects against excessive torque being applied to cable or rods. Easily adjustable. | |||||||||
| Coil Spring Sections | 1-1/4 in. x 10 ft. long with inner spring to handle torque better than hollow cables. | |||||||||
| Wheel Brake | Locks rear wheels in place or releases them in an instant. | |||||||||
| Twin V-Belts | For better power transmission. | |||||||||
| Safety Clutch | An adjustable spring-loaded clutch is mounted at the rear of the cable drive shaft. Accessible without removing machine housing. | |||||||||
| Chuck Handle | Clamps on cable or acts as "dead-man's throttle". | |||||||||
| Cable Counter | Manually operated, to record number of cables in line. | |||||||||
| Rear Cable Guide Hose | To limit cable whipping behind machine. | |||||||||
| Maximum Range | Up to 125 ft. Up to 150ft. | Up to 125 ft. Up to 150ft. | ||||||||
| Drip Guards | Two shields to protect bearings and motor from dirt and moisture. | |||||||||
| Clutch | Pull down two position handle to spin cables at 400 RPM. Lift to stop. Brake stops spinning drums instantly. | |||||||||
| Jaws | Drive both 5/8 in. and 7/8 in. cables without adjustment; also grip containers for smaller diameter cables. Keyed for longer life and less slippage. | |||||||||
| Additional Information |
You also use the drive handle to carry the machine. And when it's in position on the job, its four point base gives it rock-solid stability. A cutter holder is attached to the back of the I-95®, so your cutting heads are always with the machine. A Ground Fault Circuit Interrupter is standard equipment. Clear 1-1/2 in. - 2 in. lines with 5/16 in. x 25 ft. cable. |
To operate, just feed a cable into the line and slide the back end into the machine. The excess cable goes into a guide tube. Turn on the sealed motor, press down on the handle, and the Root 66® starts spinning the cable at 400 rpm. The cable stops rotating as soon as you lift the handle, so there's no additional torque buildup. When using a drum for small drain work, the drum stops turning when you lift the handle to the neutral position. The Root 66® has a wide four point base for greater stability. Its interlocking tubular construction also gives it excellent durability. To protect the gears from dirt and for easier cleaning, the machine has two internal plastic shields. A Ground Fault Circuit Interrupter is standard equipment. |
The Model 88® handles jobs up to 200 ft. long in lines from 3 in. to 10 in. diameter. A standard 3/4 hp capacitor motor supplies plenty of power, and an adjustable safety clutch protects cables and operator against sudden torque build-ups. Sections come in two styles: all-purpose Flexichain, which has a chain center, and the stiffer Proflex®, which has a spring center. A chain assures easier cable retrieving if the Flexichain spring should break. The inner spring in the Proflex® gives it greater stiffness, which is desirable on long or tough jobs. The outer spring is right-hand wound for faster self-feeding. Both types snap together in a second and are taken apart quickly with a spanner wrench or screw driver. With the newer "G" connector, no tension is on the locking pin when running in reverse, making it a more durable coupling. Snap on the 78L-CDC optional adapter, and you can use 6 ft. x 7/8 in. cables (6L78) to clear smaller lines. |
It's driven by a powerful 6.5 hp engine with an easily accessible throttle control on the handle. Drive speed is set at 100 to 200 rpm for municipal rods, and 200 to 400 rpm for sectional cables. The "hot-shift" transmission lets you switch from forward to reverse without the need for a clutch. The long gear shift lever is within easy reach of the operator. And features like the 3/4 in. lifetime lubricated drive chain and safety slip clutch to protect cables and rods against excessive torque build-up means low maintenance. |
||||||
| 15R10-P Proflex® Cable |
Optional 7/8 in. sectional cable (15R10-P) with Proflex® inner core gives cable more strength for cutting through difficult stoppages. Clear 2 in. - 3 in. lines up to 125 feet long with 5/8 in. x 7-1/2 ft. sections or 4 in. lines up to 150 feet long with 7/8 in. x 15 ft. sections. |
|||||||||
| I-95® Accessories | Includes cable carriers, drums for small drain work, a rear guide hose, and a tool box - standard on 7/8 in. cable units. | |||||||||
| Transportable | Light weight I-95® is easy to carry up a ladder. | |||||||||
| Sectional Cables | Four, eight and ten foot "Cable Saver" sections for the Model 88 come in the all purpose Flexichain which has a chain center, and a stiffer Proflex® which has a spring center. Proflex® is also available with a heavier duty 5/8 in. spring center. | |||||||||
| Automatic Safety Clutch | Protects cable and operator in case the cable should get caught in the line. Factory set at 18 - 20 ft. lbs. but can be adjusted easily for very heavy jobs or longer runs. | |||||||||
| Pneumatic Power Switch | Air-actuated for safety. There is no electrical connection between switch and motor. Switch can be removed from handle and used as a foot pedal when working with the cable feeding tool. | |||||||||
| No Wrench Coupler | G-CDC Cable Drive Coupler is standard on Model 88 units shipped with sections having "G" couplings. Faster uncoupling at the machine because large knurled ring can be opened instantly without wrench. | |||||||||
| Two Way Operation |
Set the Rodrunner up close to the drain opening, or on easier jobs where you have some working room, you can run the machine "lawn-mower" fashion, standing behind the machine. For close-up work, the wheel brake is set, the power switch is placed next to the machine as a foot switch, and the cable guide hose is attached. Now, the Rodrunner is ready to handle the toughest stoppages in 3-10 in. lines, as far as 200 feet away. A heavy-duty 3/4 hp motor with capacitor and overload protection spins cable at 485 rpm, an ideal speed for self-feeding into the line while protecting the cable against sudden torque build-ups. For additional protection, the Rodrunner has an adjustable slip clutch, factory set at 18 - 20 ft. lbs. An optional set of jaws (R-R10AD) enables the Rodrunner to drive 15 ft. x 7/8 in. (15R10) cables to clear smaller lines. |
|||||||||
| Optional Drum | Hold 5/16 in. and 3/8 in. cables for small drain work. | |||||||||
| Universal Jaws | Jaws handle both 7/8 in. cables (shown) or 5/8 in. cables. No adapter required. | |||||||||
| Root 66® Accessories | Includes cable carriers, drum for small drain work, a rear guide hose, and a tool box. (Standard on 7/8 in. units.) | |||||||||
| Optional Dolly | A dolly that clamps onto the Root 66® in seconds. | |||||||||
| Cable Feeding Tool | It enables cable to get around tight bends and traps by taking advantage of open-wound design of cables. Note that operator controls machine by using power switch in foot pedal mode. | |||||||||
| Folding Handle | Gives Model 88® a low profile for more convenient storage and transport. Lift handle, and locking collars slide into place for secure operation. Handle on front of frame and rear cross bar make lifting and loading into car trunk easier. | Reduces truck storage space. | ||||||||
| Note | Handle removable for easy storage. | |||||||||
|
|
||||||||||
